#IEI 2000 SERIES KEYPAD MANUAL REV 2.0 CODE#

Programmed information is stored in nonvolatile memory so it will not be lost if power is removed. NOTE: The keypad may be programmed in your shop or at the installation site. Refer to programming section to program your keypad. If you do not get the continuous light or sound then the mem ory has been corrupt and should be re-programmed with the 46 command (see option #19). Note:self test mode can be used when troubleshooting a keypad in the field. If these responses do not happen, try the test mode again and then call tech support. Either the LED s will flash or the sounder will beep 3 times.then light or sound continuously for 3 sec onds (except on the mullion). If all 12 keypresses have been verified, the keypad will enter self test mode. Connect the negative (-) lead of your power supply to the terminal strip (TS1) -V input. Connect the positive (+) lead of your power supply to the terminal strip (TS1) +V input. Call IEI for a list of product, or visit us on the web! Rev 1.04Ģ 1 2 TESTING THE KEYPAD 1. * This option is not available with some styles of keypads. The 250 comes with power supply and printer cable and connects easily to any parallel line printer (not included). The 250 can monitor up to 8 keypads simultaneously.

AUDIT TRAIL * An accurate real-time audit trail can be provided by any Command and Control Series Door-Gard with the addition of an optional model 250 Printer Interface. To use this feature, the user codes must be the same length as the master code.

#IEI 2000 SERIES KEYPAD MANUAL REV 2.0 CODE#

The user only needs to enter their code number and the relay will activate for the programmed relay time. AUTO-ENTRY This feature is used when the need for the code not to be followed by the * key is desired. This output is not available if the IEI 250 Printer Interface is used. This can be used to turn on accessories such as lights, CCTV camera, or notify a guard. KEYPAD ACTIVE OUTPUT The Command and Control Series Door-Gards can be programmed to energize a voltage output whenever a key is touched. This can be turned off through programming. KEYPRESS FEEDBACK / AUDIBLE KEYPRESS The Command and Control Series Door-Gards will acknowledge a keypress by momentarily illuminating the yellow LED like on the indoor(i), or momentarily sounding the sounder like in the sealed environmental(se) style.

This feature is especially useful when controlling an electric locking device. The main relay (if selected) will energize for the same time period as the Master Code. Upon a momentary closure, the selected outputs will energize for their programmed time. REMOTE TRIGGERING INPUT (REX) This normally open loop that by default operates the Main Relay upon activation and can be programmed to trigger any combination of outputs. The Ruggedized(r), Sealed Environmental(se), Multipad and Xtreme style provide these outputs in the form of 1 Amp Form-C relays, all other styles have negative voltage outputs with a 50mA sink. AUXILIARY OUTPUTS Auxiliary outputs can be individually timed from 1 to 90 seconds or act as a toggle switch, and may be triggered individually or in combination-by code. MAIN RELAY This is an 8 Amp (10 Amp surge) Form-C relay which can be toggled or timed from 1 to 90 seconds-by code. The Master Code is always assigned to user location one (1). Codes may be from 1-6 digits in length and digits may be repeated. CODES The Door-Gard Command and Control keypads allow up to 120 individual user codes to be valid. LED or Sounder guidance makes programming easy, and changing codes a matter of seconds for an authorized user. PROGRAMMING All programming is accomplished entirely from the front of the keypad.

FEATURES: 4 INDEPENDENT OUTPUTS 4 INDEPENDENT TIMERS ALL OUTPUTS ASSIGNABLE BY CODE ON BOARD 8 AMP FORM C RELAY 120 USERS REMOTE TRIGGERING INPUT KEYPAD PROGRAMMABLE MEMORY Non-volatile EEPROM memory means your codes and instructions will be there whether you remove power for 5 minutes or 5 years. Door-Gards accept power from a 12 or 24V AC/DC Supply. Designed for individual control of up to four devices, Door-Gard Command and Control Series keypads are the perfect choice for controlling electric locking devices, security systems, automatic operators or machinery. 1 FEATURES AND PROGRAMMING GUIDE COMMANDANDCONTROLSERIES DOOR-GARD COMMAND AND CONTROL SERIESkeypads offer field proven reliability and cost effective solutions anywhere limited control or access is desired.

Iei 2000 series keypad manual rev 2.0